Ender 3 bioprinter built for $450 by university microbiologists
According to Tom's Hardware, the build keeps most of a desktop FDM printer and swaps the extruder for a syringe pump, cutting the usual cost of bioprinting research hardware.

Key takeaways
- The Rochester team kept most of an Ender 3 and replaced the extruder with a syringe pump made from 3D-printed PETG parts.
- Tom's Hardware puts the build cost at about $450, against commercial bioprinters that usually cost more than $100,000.
- The bio-ink is bacteria mixed with alginate, printed into agarose or gelatin gels enriched with calcium ions.
- Prints in agarose stayed viable for four weeks or more, while gelatin was used where the object had to be recovered.
In this article
What the team built
Microbiologists at the University of Rochester have modified a low-cost Ender 3 FDM printer into a 3D bioprinter, according to Tom's Hardware. Their Ender 3 bioprinter cost about $450 to build, the report says, in a field where commercial machines usually sell for more than $100,000.
An FDM printer is the common desktop type that melts plastic filament and builds objects in thin layers. A bioprinter replaces that filament with a liquid carrying living material.
The machine is intended for research on engineered living materials, or ELMs. These are printed structures that contain living microbes and are designed to perform a useful task. Synthetic biology, the field behind them, treats microbes as building blocks that can be engineered for particular jobs.
The work appears in the journal ACS Applied Polymer Materials, in a paper by biologist Anne S. Meyer and colleagues titled 3D Bioprinting of Engineered Living Materials. Tom's Hardware reports that the design is open source, so other laboratories can rebuild the machine themselves.
Swapping the print head for a syringe pump
Most of the printer was left alone. The main change is the print head, where the filament extruder was replaced by a syringe pump built around custom parts printed in PETG plastic.
The pump pushes a 10 mL glass syringe fitted with a Luer-lock connector, a standard screw-on fitting for syringes and needles. A plunger mechanism drives material out and draws it back, which is how extrusion and retraction are controlled.
The software side stayed familiar. Shapes were modelled in SolidWorks, exported as STL files and sliced in Slic3r, the same broad workflow used for ordinary filament printing.
The team then adjusted the Slic3r settings to suit a 0.254 mm needle. The extrusion multiplier was cut to 0.004, giving a flow rate of 2 mL/h while the head moved at 23 mm/s.
Bio-ink, calcium and support gels
Instead of filament, the printer lays down a bio-ink made from bacteria combined with alginate, a material that gels when calcium is present. Because such a soft mixture cannot hold a shape in open air, the nozzle prints into a thick support slurry that surrounds it.
Two support gels were used. Agarose is suited to long-term incubation, and printed ELMs inside it stayed viable for four weeks or more. Gelatin was used for prints that need to be extracted afterwards.
Both slurries were enriched with calcium ions, which are charged particles. They make the alginate strands cross-link, meaning the printed material turns solid and the living bacteria are sealed inside.
Why the low price matters

The paper argues that hardware cost has held ELM research back. It also notes that expensive machines struggle to keep printed structures intact, so the Rochester team addressed both problems at once with a cheap printer and its own support material.
Bacteria are the main subject of the paper, but ELMs are not restricted to them. The reported targets include biofilms, which are thin bacterial layers, for antimicrobial treatments, organisms that break down plastic, and use in wastewater treatment.
Bacterial cellulose is another line of work, since its structural properties could suit biodegradable alternatives to plastic. Cheaper equipment could allow more laboratories to take part, and the report raises the longer-term idea of bacteria-based bioplastic filament for FDM printers.
What is still unconfirmed
The $450 cost, the comparison with machines above $100,000 and the claim that the modified printer outperforms them all come from Tom's Hardware reporting on the team's work. They have not been independently verified.
Anyone planning a similar build should treat the paper in ACS Applied Polymer Materials and the released design files as the primary sources for settings, materials and results.
Sources
Spotted a mistake? See our corrections policy. Read how News by OnDevice works in our editorial policy.



